Selection of Coolant
To maintain optimum performance and durability of your engine, use SUZUKI Genuine Coolant or equivalent.
This type of coolant is best for your cooling
system as it:
• Helps maintain proper engine temperature.
• Gives proper protection against freezing and boiling.
• Gives proper protection against corrosion and rust.
Failure to use the proper coolant can damage your cooling system. Your authorized SUZUKI dealer can help you select the proper coolant.
To avoid damaging your cooling system: • Always use a high quality ethylene glycol base phosphate type coolant diluted with distilled water at the correct mixture concentration.
• Make sure that the proper mix is 50/ 50 coolant to distilled water and in no case higher than 70/30. Concentrations greater than 70/30 coolant to distilled water will cause overheating conditions.
• Do not use straight coolant nor plain water.
• Do not add extra inhibitors or additives.
They may not be compatible with your cooling system.
• Do not mix different types of base coolants. Doing so may result in accelerated seal wear and/or the possibility of severe overheating and extensive engine/automatic transmission damage.
Engine Coolant Level Check
Check the engine coolant level at the reserve tank, not at the radiator. With the engine cool, the engine coolant level should be between the “FULL” and “LOW” marks.
Adding Engine Coolant
If the engine coolant level is below the “LOW” mark, more engine coolant should be added. Remove the reserve tank cap and add engine coolant until the reserve tank level reaches the “FULL” mark. Never fill the reserve tank above the “FULL” mark.
• The mixture you use should contain 50% concentration of antifreeze.
• If the lowest ambient temperature in your area is expected to be –35 °C (–31°F) or below, use higher concentrations up to 60% following the instructions on the antifreeze container.
• When putting the cap on the reserve tank, line up the arrow on the cap and the arrow on the tank.
Failure to follow this can result in coolant leakage.
Engine coolant is harmful or fatal if swallowed or inhaled. Do not drink antifreeze or coolant solution. If swallowed, do not induce vomiting. Immediately contact a poison control center or a physician. Avoid inhaling mist or hot vapors; if inhaled, remove to fresh air. If coolant gets in eyes, flush eyes with water and seek medical attention. Wash thoroughly after handling. Solution can be poisonous to animals. Keep out of the reach of children and animals.
Engine Coolant Replacement
1) When the engine is cool, remove the radiator cap by turning it slowly to the left until a “stop” is felt. Do not press down while turning the cap. Wait until any pressure is released, then press down on the cap and continue turning it to the left.
It is hazardous to remove the radiator cap when the engine coolant temperature is high, because scalding fluid and steam may be blown out under pressure. Wait until the engine coolant temperature has lowered before removing the cap.
2) Remove the reservoir by lifting it up, and drain the reservoir completely.
3) Loosen the drain plug attached to the lower part of the radiator and drain the engine coolant into a suitable container.
4) Reinstall the reservoir and fill it with engine coolant to the “FULL” line.
5) Tighten the drain plug on the radiator, fill the radiator with engine coolant and install the radiator cap.
6) After filling, let the engine idle for about 2 – 3 minutes to get rid of air in the cooling system. Then, stop the engine.
7) Check the engine coolant level in the radiator again. If the level has gone down, add more engine coolant.
The engine coolant must be replaced with the vehicle on level ground.
Do not use your vehicle to tow a trailer. The vehicle is not designed or intended for such use. Towing a trailer can adversely affect handling, durability and fuel economy. ...
What It All Means
The steering has a nice weight, meaning it's not overly power-assisted to the point of being twitchy on the highway, nor does it require too much effort at slow speeds. It's also precise, meaning ...
Using the Transaxle
4-Speed Automatic Transaxle Gearshift lever WARNING: Always depress the brake pedal before shifting from “P” (Park) (or “N” (Neutral) if the vehicle is stationary) to a forward or rever ...